Planning for a Cam Change

Today's dissertation is about planning for a cam change. You have changed exhaust, upgraded the air cleaner/carb selection, and now its time to move to the next step. Using the highest lift, longest duration cams, are not always your best choice. Even though in some combinations they can work very, very well, using them with components that are not designed to compliment the cam can often disappoint. Here are some important points.

- We have to decide what RPM we want to develop the best power at.
- When we establish that RPM, there is no free lunch. In order to perform better at high RPM, we sacrifice low-end performance. Also, the inverse is true. Good performance at low RPM hurts top end performance. There is no way around this.
- If in doubt, you are always better choosing the conservative choice.

After making the decision about where we want to build power, we can make some educated choices. A Review of Skid Steer Snowblowers . Mikuni North America gave me a nice guide that I have used in cam choices for a long time.

Cam Basics:

Correct cam selection is the single most difficult choice facing the performance enthusiast. And, unfortunately, we get it wrong about as often as we get it right. An incorrect cam choice can result in decreased real-world performance if the selected cam's operating range is not matched to riding style.

The operating range of any Harley engine is determined by a number of factors and the cam design is one of the most influential. If the cam design is not matched to the other components, and it's not matched to the desired engine power band (rpm range), then the engine's performance will be disappointing. No amount of carburetor tuning can compensate for having the wrong cam.
To get the right cam design, you need to do two things: First, decide upon the rpm range you want to improve. Secondly, use the list provided below and cam catalogs to select a cam design that begins to work at the lower rpm of the power range you have chosen. You'll probably be surprised to learn how few of the available cam designs fit your expectations.

Cam timing: What matters?

The most important cam-timing event is the intake valve-closing angle. The intake closing point determines the minimum rpm at which the engine begins to do its best work. The later the intake valves close, the higher the rpm must be before the engine gets on the cam.

Long duration, late closing cam designs are necessary to drag the last bit of power out of an engine. Unfortunately, these same cams can perform poorly under more normal riding conditions. In the quest for maximum power output, many-too-many Harley owners choose a late closing, high-rpm cam for their engine. The problem with such choices is that the engine seldom spends time in the rpm range favored by such cams.

The majority of virtually any Harley motor's life is spent in the mid-portion of its rpm limits, between 2000 and 4000 rpm. At open-road cruising speeds, that range is more like 2500 to 3500 rpm. With current Big Twin gearing, top gear at 2500 rpm returns a road speed of 55 mph and 3500 delivers 84 mph. Riders sometimes putt around at 2000 or less. help me with my compaq pc. Even when accelerating to cruising speed, few of us use more than 4000 - 4500 rpm as a shift point. Very seldom, in day-to-day use, do our engines get near 5000 rpm, let alone 6000.
Even the mildest of Harley-Davidson's aftermarket cams (Evo or Twin Cam) do their best work above 3000 rpm. At 2000, the majority of these cams seldom perform significantly better than stock cam(s).

The rpm at which a Big Twin gets happy can be predicted by the closing point (angle) of the intake valves. The angle is expressed as the number of degrees After Bottom Dead Center (ABDC) that the valves reach .053 from being fully seated.

The calculations below predict the rpm at which the engine gets on the cam based on the closing angle of the intake valves.

- 30 degrees = 2400 rpm
- 35 degrees = 3000 rpm
- 40 degrees = 3600 rpm
- 45 degrees = 4000 rpm
- 50+ degrees = 4500 rpm

These relationships are approximate but should hold true to within 200 rpm or so. They also assume that all other tuning factors, exhaust, ignition, etc., are operating correctly.

If you have one of the late closing cam designs installed, say one that closes the intake valves later than 40 degrees, then you cannot expect excellent performance at 2000 rpm. No carburetor adjustment, ignition adjustment or exhaust system can change this.

You can find more information and all the motorcycle parts and accessories you need at J&P Cycles. J&P Cycles carries Harley parts, Vintage Harley parts and metric cruiser parts.